main logo

THE EUROPEAN MARKET FOR PLASTICS AUTOMOTIVE COMPONENTS

Plastics are the answer to today?s complex transportation needs. Everywhere plastics are in motion. Manufacturers are turning to plastics not only because, plastics make cars more energy efficient by reducing weight, but they provide durability, corrosion, resistance, toughness, design flexibility, ease of colouring, resiliency and high performance at low costs.

As the old Millennium ended (at least symbolically), sales of vehicles in Western Europe reached an all-time high of 15 million units. The use of plastics in automobiles during the past century has been significant - in fact, historically one might say there have been plastics in automobiles almost as long as there have been plastics.

The first automobiles came out in 1900 and for many years cellulose nitrate sheet was used as side curtains in horse and buggy rigs. Cellulosics were later used for moulding the steering wheel, and some phenolics and ureas were employed for electrical components and control knobs.

The real plastics revolution in automotive industry began in 1950 when thermoplastics made their debut, starting with ABS and going on to polyamide, polyacetal and polycarbonate. The introduction of alloys and blends of various polymers made it possible to tailor properties to fit certain performance requirements that single resin could not provide, the first was probably polystyrene-modified polyphenylene oxide.

During the 1960s, however, thermosetting composites knew a considerable development in the automotive industry, firstly complete monocoque bodies, in glass fibre reinforced polyester resin, and later with factory-made polyester/glass combinations that could be moulded by compression and a form of injection: Sheet Moulding Compounds (SMC) and Bulk Moulding Compounds (BMC).

Since those beginnings, the use of plastics components in automotives has undergone enormous growth - particularly during the last 20 years ? by 2000, over 105 kg of plastics were used in the average vehicle. Mounting costs are being met by the ability of plastics to be moulded into components of complex geometries, often replacing several parts in other materials, and offering integral fitments that all add up to easier assembly, helping to reduce costs on the assembly line.

The lightness in weight of plastics has proved itself a genuine benefit to the automotive industry, not only in reducing overall weight of cars, in order to reduce fuel consumption to legislated limits, but also in allowing more sophisticated systems and components - including safety systems - to be included in the modern car, without paying the penalty of additional weight.

In practical terms, this has allowed more sophisticated heating ventilation and climate control systems to be installed in the car of today, with in-car entertainment and information systems, not to mention providing the additional safety of airbags - all without adding to overall weight.

Without plastics, it is estimated that today's cars would be around 200-300 kg heavier. That saves 0.5 litre per 100 km which represents 750 litres for a car with a lifetime of 150,000 km.

Many types of polymers are used in more than 1,000 different parts of all shapes and sizes. Although up to 13 different polymers may be used in a single car model, just three "families" make up some 66 % of the total plastics used in a car: polypropylene (32 %), polyurethane (17 %) and PVC (16 %).

A quick look inside any model of car shows that plastics are now used in exterior and interior components such as bumpers, doors, safety and windows, headlight and sideview mirror housing, trunk lids, hoods, grilles and wheel covers. the passenger compartment is dominated by plastics.

Recent years have seen a veritable invasion of the under-bonnet region by plastics, leading to widespread adoption of large (1.5 to 2.5 kg) mouldings for air intake manifolds. These are not only half the weight of their metal counterparts: they optimise the airflow to the engine, helping to make it more efficient, and also playing a valuable role in reducing noise levels. Moulded in glass fibre reinforced nylon, these are highly sophisticated parts, marking the true arrival of plastics as engineering materials in their own right.

How plastics save weight in cars

The "invasion" of plastics in the engine compartment is by no means over. Automible engineers are working together closely now to optimise other systems, integrating injection and blow moulded parts, and harnessing plastics and elastomers that give a range of properties from "soft" to "hard", but can be moulded simultaneously or in sequence, offering a better product without expensive assembly work.

Plastics are also finding their way into the structural design of cars. Intensive development of thermoplastics has opened the way to production of individual bodywork panels by injection moulding, to meet the high temperature of the paint stoving ovens used by the automotive industry, and electrically-conductive grades, for electrostatic painting.

The most complicated design problem the tank fuel system has been solved thanks to plastics. Another important area of development is in fuel systems. Again, this is an area which (for the safety of all) is a focal point for legislation, to conserve fuel and minimise emissions.

For more than a decade, all-plastics fuel tanks have been produced, by blow-moulding in ultra-high molecular weight high density polyethylene. These lightweight tanks by their good mouldability, give more design freedom to fit tanks in difficult spaces.

It is estimated that some 90 % of all new cars in Europe have plastics tanks, and the technology has been exported to North America, where about 70 % of cars now use this system. In Japan, the market share is considerably lower, at about 7 %, but considerable growth is expected there also, to meet tighter fuel emission standard. The development of fuel tanks presents a remarkable demonstration of the potential of plastics. Originally, tanks were treated internally to reduce the permeability of polyethylene. But, to meet tightening emission standards, particularly in the USA, multi-layer tanks are blow moulded, incorporating a layer of a high barrier polymer, and tie-layers to bond it to the structural inner and outer layers. A sixth layer is usually added, to re-use the scrap produced in manufacturing.

Multi-layer extrusion technology is coming rapidly into the production of plastics fuel tubing, to reduce permeability to nearly zero and, where required, to include electrical conductivity.

The next stage will be the integration of the total fuel system, to be designed as a complete unit. This will almost certainly change the methods of assembly and connection (as research shows that it is at these points that there is greatest risk of emissions). Again, we may expect that plastics will rise to meet this challenge.

Reinforced thermosetting resins also have a key part to play. While there is nearly fifty years of experience of the use of glass fibre-reinforced resins in production of bodywork, this has tended to be restricted by the nature of the material to low-volume production (of sports cars and "specials"). More recently, however, great strides have been made in the development of processes for moulding fibre-reinforced polyesters and polyure-thanes at viable mass-production levels, and there is an increasing number of exterior bodywork panels and bumper systems that are produced in volume in these thermosetting materials.

Perhaps the greatest challenge to plastics in the automotive sector, however, is in recycling. Although the automotive industry has probably the best record of all industries when it comes to recycling its materials, with an average of around 75 %, the requirements now laid down by the European Union set even higher targets, and it is clear that something more productive must be done with plastics than dumping them in landfill.

For its part, the plastics industry has effectively demonstrated that its thermoplastics can readily be recycled by conventional melt processing, and its thermosetting composites can be handled by grinding to powder and reuse in new compounds. For both, the industry is fast developing chemical technologies.

Most of the automotive groups, in partnership with plastics material suppliers and the key automotive moulders, have developed "closed loop" approaches, in which certain parts are designated to be recycled to produce other parts. Collection and dismantling of the complex sub-assemblies of an automobile will certainly prove a challenge, but is not insurmountable.

It has also been demonstrated that plastics open up more avenues to efficient recycling than simply reprocessing the materials by mechanical means. Technologies are being introduced that will permit mixed (and contaminated) plastics parts to be broken down chemically, for reformulation as new plastics. Nor should the high calorific content of plastics be ignored: in modern incineration plants it can return that value, in heating and saving conventional fuel.

The real challenge now, both to the automotive industry and its plastics suppliers, is to work together to develop new assemblies that not only meet cost/performance requirements but also allow easier dismantling and recycling.

It can be seen that the development of plastics in automotives is all the time prompting engineers to take an integrated systems approach. This can only be aided by the emergence of "Tier One" suppliers to the industry - large, well-financed groups, operating globally, able to undertake the engineering, manufacture of whole modules, and deliver them to assembly lines Just-In-Time.

Computer-aided design and manufacturing systems also make this possible, allowing "simultaneous engineering" by all the participants in a project.

Driver and passenger "cockpit" modules, complete doors, air control systems and fuel systems are even now being developed by such giants.

Parallel with them, in Europe also, large plastics engineering groups are also emerging, both integrated with the new groups and independent of them. They not only have the moulding equipment and the latest CAD/CAE systems. They also have behind them decades of human skill, in working with plastics to get the best value from these materials.

In short, plastics meet the challenges of an industry whose demands are greater than ever. While motorists want improved performance cars with greater comfort, reliability, fuel savings, style and lower prices, society demands lower pollution levels and increased recovery at end of life.

Continious innovation is a key feature in the use of plastics in cars. As the needs increase, new plastic materials are being created to meet them.

documents


links

EuPC's mission is to create a good trading environment for Plastics Converters in Europe.

EuPC Survey - Study on the Competitiveness of Plastics Converters in Europe
EuPC Annual Meeting: Innovation meets the circular economy
Polymers for Europe Alliance
EuPC General Assembly 2015 (Warsaw)
Plastics Recycling Annual Meeting 2016
Waste Free Oceans Logo
polymercomplyeurope.eu
Pieweb.com
List of EuPC Members (national plastics associations)
Vinyl Plus - Vinyl Foundation